Systems
|
 |
· Ensure that there is proper AC and DC power (Also - see Electrical below)
|
 |
· Inspect under all floor boards for possible problems
|
 |
· Inspect Engine room for problems
|
 |
· Ensure Propane and fume detector Alarm System working properly
|
 |
· Ensure Engine Room Fire Extinguisher properly charged
|
Recharged in Spring 2005
|
· Clean all raw water filtration systems:
|
 |
· AC Air Conditioner
|
Cleaned
|
· AC Refrigeration
|
Cleaned
|
· DC Refrigeration
|
Cleaned
|
· Gray water outflow systems (Fresh and Raw)
|
 |
· Galley Sink
|
Disassembled and Cleaned
|
· Aft & forward shower systems
|
Disassembled and Cleaned
|
· Filters for Heads
|
Cleaned
|
· Pre Filter for Water Maker at seacock intake
|
Cleaned
|
· Heads (Forward and Aft)
|
 |
· Check Heads for leaks and flushing
|
 |
· Check Head holding tank monitor
|
 |
· Verify Macerator working Forward
|
 |
· Verify Macerator working Aft
|
 |
· Change charcoal filter in fresh water filter to fill tanks from dock
|
Completed
|
· Run air conditioner in both heat and cool modes; monitor performance
|
 |
· Run water maker; replace pre-filters as needed; check for leaks,
check flow rate >10 GPH, check water quality < 500 PPM
|
Re-pickled Jan 2006
|
· Run refrigerators; monitor performance.
|
 |
· Lubricate and adjust steering.
|
 |
· Monitor solar- and wind-power generators
|
Reassembled and Install
Wind Generator
|
· Check tension on steering pedestal motor chain for autopilot.
|
 |
· Check Tank Tender working
|
Must repair
|
· Replace ship's zincs
|
 |
· Prop
|
Sep-05
|
· Shaft
|
Sep-05
|
· Main zinc for ship
|
Sep-05
|
· Two R3 zincs
|
Sep-05
|
· Bow thruster zinc
|
Sep-05
|
· Genset zinc
|
 |
· Clean prop & grease
|
 |
· Check cutlass bearing
|
 |
· Exercise Windlass
|
 |
· Exercise Bow Thruster
|
 |
· Check Washer / Dryer
|
 |
· Clean all air filters for Air Conditioners:
|
Ongoing
|
· Master State Room
|
Ongoing
|
· Saloon
|
Ongoing
|
· Forward Berth
|
Ongoing
|
· Clean exhaust filter for dryer on washer / dryer
attachment to cowl in 3rd stateroom
|
Ongoing
|
 |
 |
Electrical Systems
|
 |
· EQUALIZE BATTERIES (All 3 Banks) USING CONSTANT CHARGE
BATTERY CHARGER (e.g.. Prosine 3000) for ~ 1/2 hour every six months
or more if needed (Even if you do not bring batteries down below 12.2. volts)
|
6-Jan
|
· Clean & tighten battery terminals
|
 |
· Check battery fuses for continuity
|
 |
· Exercise Breakers and main switches
|
 |
· Ensure Tie Switch for Battery Banks (Engine & House) working properly
|
 |
· Ensure that Engine Alternator and House Alternator can charge House and/or
Engine battery banks using Tie Switch
|
· Ensure Glendenning Electrical Cord retractor system working properly
|
 |
· Test lights, and clean contacts or replace bulbs as needed:
|
 |
· Navigation
|
 |
· Tri-color
|
 |
· Running
|
 |
· Back-up Elevated stern light
|
 |
· Steaming
|
 |
· Anchor
|
 |
· Strobe
|
 |
· Spreader
|
 |
· Compass
|
 |
· Boom Light
|
 |
· 3 deck lights
|
 |
· Pole Light facing Forward
|
Purchase & replace
|
· Pole Light facing Aft
|
 |
· Cockpit lights
|
 |
· Interior Lights
|
 |
· Cabin overhead lights
|
 |
· Cabin reading lights
|
 |
· Closet lights
|
 |
· Rope Lights
|
 |
· Other Lights
|
 |
· Exterior Engine Panel Lights
|
 |
· Refrigerator/Freezer lights
|
 |
· Flash Lights in each cabin
|
 |
· Nav Station Instrument Panel Lights
|
 |
· Check lights in aft lazaretto (Dive Compressor area)
|
 |
· Check lights in Port & Starboard lazarettes
|
 |
· Check lights in Sail Locker
|
 |
· Check lights in Anchor locker
|
 |
· Check Calabash Cockpit Light
|
Replace light and wiring
|
· Check Bimini Lights
|
 |
· Test Microwave Oven
|
 |
 |
 |
· Engine Start
|
 |
· Clean engine room
|
 |
· Check oil level
|
 |
· Check transmission-oil level.
|
Replace Jan 06
|
· Check Coolant level.
|
 |
· Change Water Pump Impeller
|
Replace Jan 06
|
· Exercise and open the inlet seacock
|
 |
· Transmission, coupling, check
|
 |
· Clean engine water strainer
|
 |
· Change fuel filters both primary and secondary
|
 |
· Adjust belt tension
|
 |
· Check Motor Mounts
|
 |
· Exercise and lubricate throttle controls
|
 |
· Grease blue steering cable nipples
|
 |
· Tighten all hose clamps.
|
 |
· Inspect all hoses for chafe or bulging
|
 |
· Snug up all bolts on engine accessories
|
 |
· Exercise and open fuel-tank petcocks
|
 |
· Run Fuel Polishing system on each tank
|
 |
· Clean and lubricate articulating props
|
 |
· Flush engine
|
 |
· Clean / boil anti-siphon valve (Intake and Exhaust)
|
6-Jan
|
· Check water alarms for Racor primaries and Yanmar secondary fuel filters
|
 |
 |
 |
Engine Running
|
 |
· Start Engine by holding in kill switch for
15 seconds to pre-lube engine and then start
|
 |
· Monitor oil pressure.
|
Replace sender with dual
|
· Monitor exhaust
|
 |
· Test transmission shifting.
|
 |
· Look for oil leaks.
|
 |
· Look for raw-water and coolant leaks.
|
 |
· Look for fuel leaks around hoses and filters.
|
 |
· Verify temperature after starting
|
 |
· Create new temperature curves using spot meter & verify
|
Use new spot meter
|
· Check alternator output on Link 20 System
|
 |
· Monitor tachometer for regularity
|
 |
· Exercise the shaft-brake release
|
Reinstall in March
|
· Monitor the PYI drip less shaft seal - (drip rate >> 5 drops per minute)
|
 |
· Valve tap settings
|
 |
 |
 |
Genset
|
 |
· Check oil level
|
 |
· Check Coolant level.
|
 |
· Change Water Pump Impeller
|
6-Jan
|
· Exercise, lubricate, and open the inlet seacock.
|
 |
· Clean water strainer
|
 |
· Change fuel filters both primary and secondary
|
6-Sep
|
· Exercise and lubricate throttle controls
|
 |
· Tighten all hose clamps.
|
 |
· Inspect all hoses for chafe or bulging
|
 |
· Snug up all bolts on engine accessories
|
 |
· Exercise and open fuel-tank petcocks
|
 |
· Replace Pencil Zinc
|
6-Jan
|
· Flush engine
|
 |
· Clean / boil anti-siphon valve (Intake and Exhaust)
|
6-Jan
|
 |
 |
Sailing and Rigging
|
 |
· Inspect rig for rust and wear
|
Cleaned all running & standing rigging March 06
|
· Inspect and exercise Backstay Adjusters
|
Replace internal Port Rod
|
· Operate all sail furlers
|
 |
· Check release pins working properly for:
|
 |
· Spinnaker Pole
|
 |
· Reaching Strut
|
 |
· Whisker Pole
|
 |
· Halyard shackles
|
 |
· Check integrity of mast boot, Check water tight mast / deck seal
|
Redo Sealant on mast deck ring
|
· Inspect turnbuckles and toggles for hairline cracks and rust
|
Rechrome turnbuckles
|
· Check all cotter pins and rings
|
 |
· Operate winches; grease as needed
|
 |
· Operate clutches; lubricate
|
 |
· Check all running rigging for chafe
|
 |
· Inspect all sheets
|
 |
· Genoa
|
 |
· Main
|
 |
· Staysail
|
 |
· Spinnaker
|
 |
· Boom Preventer
|
 |
· Check all lines for proper whipping.
|
Whipped Dinghy Lift Lines
|
· Sails; Inspect seams, corners, battens, and pockets
(Should be done when sails are stored)
|
Remove 10 CM from Genoa
, cleaned all sails, Stiffen main leech
|
· Check all masthead hardware
|
 |
· Reinstall Main, Genoa and Staysail
|
 |
· Polish halyard shackles
|
 |
· Check luff rods for burrs
|
 |
· Put "preventer" ties on all Shackles to secure sails
|
 |
· Attach Sheets
|
 |
· Adjust roller furlers
|
 |
· Raise Sails
|
 |
· Refurl
|
 |
· Lubricate fastpins for aft guard rail gate, life raft and MOM8
|
 |
· Protect Aluminum whisker pole and ends of Spinnaker and Whisker poles with AL Protect
|
 |
· Place safety retainers (UV protected electrical wire tires) on all items to be secured:
|
 |
· Main Halyard (Upper and Lower)
|
 |
· Genoa Halyard (Upper and Lower)
|
 |
· Stays'l Halyard (Upper and Lower)
|
 |
· Lock Pins on Genoa and Stays'l Furlers
|
 |
· Lock Pins on Running Back Blocks
|
 |
· Other as identified
|
 |
· Ensure that Spare Mainsail Battens stored in Boom are properly lashed with ties
|
 |
· Inspect bungee cords holding upright:
|
Redone
|
· Genoa Outhaul
|
 |
· Deck Blocks for running backs
|
 |
· Selden Mast Motor plug
|
 |
 |
 |
· Safety
|
 |
· Verify expiration dates of safety gear (Actual dates: Safety Gear)
|
 |
· EPIRB Registrations current (See Safety Gear)
|
 |
· EPIRB Batteries (See Safety Gear)
|
Replaced Jan 06
|
· Life Raft Inspection (See Safety Gear)
|
Replaced Jan 06
|
· Flares (See Safety Gear)
|
 |
· Check fire extinguishers
|
 |
· Inspect Life Sling
|
 |
· Inspect MOM8 System
|
 |
· Inspect Life Jackets
|
 |
· Inspect Horsehoe Ring and quick release Mechanisms
|
 |
· Inspect quick release mechanism for life raft
|
 |
· Inspect seizing wires of anchor shackles and snubber
|
 |
· Operate Windlass; monitor performance.
|
 |
· Operate Bow Thruster
|
 |
· Inspect Sea Anchor
|
 |
· Inspect & Clean lifelines for integrity.
|
 |
· Pressure-test propane appliances
|
 |
· Inspect cockpit drains for blockage
|
 |
· Check and inspect contents of ditch bag
|
 |
· Inspect and replace as necessary medical supplies
|
 |
· Inspect Survivor 06 Hand Held Water Maker, flush,
test and recharge with biocide
|
Repickled Jan 2006
|
· Inspect manual compass and compensate if necessary
|
 |
 |
 |
· Electronics & Computers
|
 |
· Clean VHF coax.
|
 |
· Monitor VHF transmission power
|
 |
· Verify Link 20 system working properly
|
 |
· Verify Prosine 3000 working properly
|
 |
· Bring up ships computers
|
 |
· Test ships computer network/Blue tooth Interfaces
|
 |
On Desk Top
|
 |
Nav Computer
|
 |
GPRS Phone
|
 |
Accnt Computer
|
 |
· Test WIFI Connection
|
 |
· Test Packet Radio
|
 |
· Test SSB and SWR Meter
|
 |
· Test SSB Autotuner
|
 |
· Test Instrument to computer Interface
|
 |
· Inspect 2 GPS systems
|
 |
· Northstar 941
|
Rewire Ant Wire through Arch
|
· Ray Marine 300 WAAS
|
 |
· Test RADAR and interfaces to computer network and GPS
|
 |
· Test Ocens system
|
Got new 4.1.15 Update
|
· Test Winlink and SailMail
|
 |
· Test IMARSAT-C
|
Must Retest
|
· Test Printer, Scanner and Smart Card interfaces
|
 |
· Clean depth-sounder and log/speedometer transducer O-rings
|
 |
· Clean & tighten all instrument connections
|
 |
· Check stereo and TV systems, cable/antenna/VCR & DVD inputs
|
Redid TV Schematic
|
· Check interface to cockpit LCD system
|
 |
· Verify that recording Barometer is working properly
|
 |
· Inspect Weatherstation System
|
 |
· Inspect WxFax system
|
 |
· Inspect Navtext system
|
 |
· Verify GPIRB working correctly
|
 |
· Check GPS interfaces to:
|
 |
· EPIRB
|
 |
· VHF
|
 |
· SSB
|
 |
· Check HF Antenna Connector to Backstay, clean or replace
|
 |
· Check Vetus recording barometer
|
 |
· Check grounds:
|
 |
· NavTex Antenna
|
 |
· Furuno WxFax Antenna
|
 |
· Antenna Tuner
|
 |
· HF Radio Ground
|
 |
· Computer Maintenance Items for all 5 computers:
|
 |
· Clean disk files
|
 |
· Copy all data files to appropriate subdirectories on USB Hard Disk Drive
|
 |
· Run Norton System Works Diagnostic and fix any exiting problems
|
 |
· Defrag
|
 |
· Load applicable charts for intended cruising areas
|
 |
· Ensure that the following software is operational on laptop & desktop and at least one backup laptop
|
· Nobeltec
|
 |
· Ocens (Not on Desktop)
|
 |
· Airmail
|
 |
· ScanDisk Reader
|
 |
· Portable USB hard disks for data backup
|
Added Additional 160MB ext
|
 |
 |
Plumbing
|
 |
· Clean and Test electric bilge pumps
|
 |
· Exercise manual Bilge Pump
|
 |
· Clean Bilge
|
 |
· Clean & Test float switches
|
 |
· Test bilge alarm float switch
|
 |
· Exercise and lubricate head pumps and Y-valves.
|
 |
· Run and test freshwater pumps.
|
Replaced 2 FW pumps Jan 06
|
· Exercise and lubricate all seacocks.
|
 |
· Test hot water heater
|
 |
· Check water pressure tank > 10 - 15 PSI
|
 |
· Check salt water deck pumps
|
 |
· Check fresh water deck pumps
|
 |
· Check aft transom shower
|
 |
· Check fresh water backup pump system
|
Replaced 2 FW pumps Jan 06
|
· Check Hot Water Heater for leaks and proper operation
|
 |
· Every second year replace Torrid Hot Water Heater magnesium anode rod
|
 |
· Clean forward and aft heads
|
 |
· Test electric head
|
 |
· Test holding tank monitor forward and aft heads
|
Clean, & repair reed Switch Floats and Monitor
|
· Test Macerators
|
Fix Automatic Switch
|
· Lubricate Forward head
|
Sep 2005
|
· Clean holding tanks & Put additives in holding tanks
· Clean aft head Y-Valve and Head overboard Tubes
|
Mar 06
Jan 06
|
 |
 |
Other
|
 |
· Wash & Paint bottom
|
Mar 06
|
· Clean Radio Grounds (2) for HF Radio & Tuner
|
Mar 06
|
· Clean Depth Sounder
|
Mar 06
|
· Clean Hull Speed Transducer
|
Mar 06
|
· Wax Topsides
|
Mar 06
|
· Wax deck
|
Nov 2005
|
· Polish SS
|
Nov 2005
|
· Clean dodger and Bimini
|
Nov 2005
|
· Protect dodger and Bimini with 303
|
 |